Product Code Database
Crucible steel is steel made by melting pig iron, cast iron, iron, and sometimes steel, often along with sand, glass, , and other fluxes, in a crucible. Crucible steel was first developed in the middle of the 1st millennium BCE in Southern India and Sri Lanka using the wootz process.
In ancient times, it was not possible to produce very high temperatures with charcoal or coal fires, which were required to melt iron or steel. However, pig iron, having a higher carbon content and thus a lower melting point, could be melted, and by soaking wrought iron or steel in the liquid pig-iron for a long time, the carbon content of the pig iron could be reduced as it slowly diffusion into the iron, turning both into steel. Crucible steel of this type was produced in South and Central Asia during the Middle Ages.
This generally produced a very hard steel, but also a composite steel that was inhomogeneous, consisting of a very high-carbon steel (formerly the pig-iron) and a lower-carbon steel (formerly the wrought iron). This often resulted in an intricate pattern when the steel was forged, filed or polished, with possibly the most well-known examples coming from the wootz steel used in
which contributed to the distinctive water pattern. The steel was usually worked very little and at relatively low temperatures to avoid any decarburization, hot short crumbling, or excess diffusion of carbon.
With a carbon content close to that of cast iron, it usually required no heat treatment after shaping other than air cooling to achieve the correct hardness, relying on composition alone. The higher-carbon steel provided a very hard edge, but the lower-carbon steel helped to increase the toughness, helping to decrease the chance of chipping, cracking, or breaking. A History of Metallography by Cyril Stanley Smith. MIT Press, 1960. pp. 16–24
In Europe, crucible steel was developed by Benjamin Huntsman in England in the 18th century. Huntsman used coke rather than coal or charcoal, achieving temperatures high enough to melt steel and dissolve iron. Huntsman's process differed from some of the wootz processes in that it used a longer time to melt the steel and to cool it down and thus allowed more time for the diffusion of carbon.R. F. Tylecote (1992). 9780901462886, Maney Publishing, for the Institute of Materials. ISBN 9780901462886 Huntsman's process used iron and steel as raw materials, in the form of blister steel, rather than direct conversion from cast iron as in puddling or the later Bessemer process.
The ability to fully melt the steel removed any inhomogeneities in the steel, allowing the carbon to dissolve evenly into the liquid steel and negating the prior need for extensive blacksmithing in an attempt to achieve the same result. Similarly, it allowed steel to be casting by pouring into molds. The use of fluxes allowed nearly complete extraction of impurities from the liquid, which could then simply float to the top for removal. This produced the first steel of modern quality, providing a means of efficiently changing excess wrought iron into useful steel. Huntsman's process greatly increased the European output of quality steel suitable for use in items like knives, tools, and machinery, helping to pave the way for the Industrial Revolution.
Various methods were used to produce crucible steel. According to Islamic texts such as al-Tarsusi and al-Biruni, three methods are described for indirect production of steel.Feuerbach et al. 1997, 105 The medieval Islamic historian Abu Rayhan Biruni (c. 973–1050) provides the earliest reference of the production of Damascus steel.Feuerbach et al. 1998, 38 The first, and the most common, traditional method is solid state carburization of wrought iron. This is a diffusion process in which wrought iron is packed in crucibles or a hearth with charcoal, then heated to promote diffusion of carbon into the iron to produce steel.Feuerbach et al. 1995, 12 Carburization is the basis for the wootz process of steel.
The second method is the decarburization of cast iron by removing carbon from the cast iron.
The third method uses wrought iron and cast iron. In this process, wrought iron and cast iron may be heated together in a crucible to produce steel by fusion. In regard to this method Abu Rayhan Biruni states: "this was the method used in Hearth". It is proposed that the Indian method refers to Wootz carburization method; i.e., the Mysore or Tamil people processes.Srinivasan 1994, 56
Variations of co-fusion process have been found primarily in Persia and Central Asia but have also been found in Hyderabad, IndiaFeuerbach et al. 1998, 39 called Deccani or Hyderabad process. For the carbon, a variety of organic materials are specified by the contemporary Islamic authorities, including pomegranate rinds, acorns, fruit skins like orange peel, leaves as well as the white of egg and shells. Slivers of wood are mentioned in some of the Indian sources, but significantly none of the sources mention charcoal.
While crucible steel is more attributed to the Middle East in early times, Pattern welding swords, incorporating high-carbon, and likely crucible steel, have been discovered in Europe, from the 3rd century CE, particularly in Scandinavia. Swords bearing the brand name Ulfberht, and dating to a 200-year period from the 9th century to the early 11th century, are prime examples of the technique. It is speculated by many that the process of making these blades originated in the Middle East and subsequently had been traded during the Volga Trade Route days.See:
In the first centuries of the Islamic period, some scientific studies on swords and steel appeared. The best known of these are by Jabir ibn Hayyan 8th century, al-Kindi 9th century, Al-Biruni in the early 11th century, al-Tarsusi in the late 12th century, and Fakhr-i-Mudabbir 13th century. Any of these contains far more information about Indian and damascene steels than appears in the entire surviving literature of classical Greece and Ancient Rome.Bronson 1986, 19
European accounts from the 17th century onwards have referred to the repute and manufacture of "wootz", a traditional crucible steel made specially in parts of southern India in the former provinces of Golconda, Mysore and Salem. As yet the scale of excavations and surface surveys is too limited to link the literary accounts to archaeometallurgical evidence.Griffiths and Srinivasan 1997, 111
The proven sites of crucible steel production in south India, e.g. at Konasamudram and Gatihosahalli, date from at least the late medieval period, 16th century.Srinivasan 1994, 52 One of the earliest known potential sites, which shows some promising preliminary evidence that may be linked to ferrous crucible processes in Kodumanal, near Coimbatore in Tamil Nadu.Ranganathan and Srinivasan 2004, 117 The site is dated between the third century BCE and the third century CE.Craddock 2003, 245 By the seventeenth century the main centre of crucible steel production seems to have been in Hyderabad. The process was apparently quite different from that recorded elsewhere.Craddock 1995, 281 Wootz from Hyderabad or the Deccani process for making watered blades involved a co-fusion of two different kinds of iron: one was low in carbon and the other was a high-carbon steel or cast iron.Moshtagh Khorasani 2006, 108 Wootz steel was widely exported and traded throughout ancient Europe, China, the Arab world, and became particularly famous in the Middle East, where it became known as Damascus steel.Srinivasan 1994Srinivasan & Griffiths
Recent archaeological investigations have suggested that Sri Lanka also supported innovative technologies for iron and steel production in antiquity.Ranganathan and Srinivasan 2004, 125 The Sri Lankan system of crucible steel making was partially independent of the various Indian and Middle Eastern systems.Bronson 1986, 43 Their method was something similar to the method of carburization of wrought iron. The earliest confirmed crucible steel site is located in the Knuckles range in the northern area of the Central Highlands of Sri Lanka dated to 6th–10th centuries CE.Feuerbach 2002, 168 In the twelfth century the land of Serendib (Sri Lanka) seems to have been the main supplier of crucible steel, but over the centuries production slipped back, and by the nineteenth century just a small industry survived in the Balangoda district of the central southern highlands.Craddock 1995, 279
A series of excavations at Samanalawewa indicated the unexpected and previously unknown technology of west-facing smelting sites, which are different types of steel production.Juleff 1998, 51 These furnaces were used for direct smelting to steel.Juleff 1998, 222 These are named "west facing" because they were located on the western sides of hilltops to use the prevailing wind in the smelting process.Juleff 1998, 80 Sri Lankan furnace steels were known and traded between the 9th and 11th centuries and earlier, but apparently not later.Juleff 1998, 221 These sites were dated to the 7th–11th centuries. The coincidence of this dating with the 9th century Islamic reference to Sarandib is of great importance. The crucible process existed in India at the same time that the west- facing technology was operating in Sri Lanka.Juleff 1998, 220 Excavations of the Yodhawewa (near Mannar) site (in 2018) have uncovered a lower half of a bottom spherical furnace and crucible fragments used to make crucible steel in Sri Lanka during the 7th-8th centuries AD. The crucible fragments uncovered at the site were similar to the elongated tube-shaped crucibles of Samanalawewa.
The two most prominent crucible steel sites in eastern Uzbekistan carrying the Ferghana Process are Akhsiket and Pap in the Ferghana Valley, whose position within the Great Silk Road has been historically and archaeologically proved.Rehren and Papakhristu 2000, 58 The material evidence consists of large number of archaeological finds relating to steel making from 9th–12th centuries CE in the form of hundreds of thousands of fragments of crucibles, often with massive slag cakes. Archaeological work at Akhsiket, has identified that the crucible steel process was of the carburization of iron metal.Rehren and Papakhristu 2000 This process appears to be typical of and restricted to the Ferghana Valley in eastern Uzbekistan, and it is therefore called the Ferghana Process.Rehren and Papakhristu 2000, 67 This process lasted in that region for roughly four centuries..
Evidence of the production of crucible steel have been found in Merv, Turkmenistan, a major city on the 'Silk Road'. The Islamic scholar al-Kindi (801–866 CE) mentions that during the ninth century CE the region of Khorasan, the area to which the cities Nishapur, Merv, Herat and Balkh belong, was a steel manufacturing centre.Feuerbach 2003, 258 Evidence from a metallurgical workshop at Merv, dated to the ninth- early tenth century CE, provides an illustration of the co-fusion method of steel production in crucibles, about 1000 years earlier than the distinctly different wootz process.Feuerbach 1997, 109 The crucible steel process at Merv might be seen as technologically related to what Bronson (1986, 43) calls Hyderabad process, a variation of the wootz process, after the location of the process documented by Voysey in the 1820s.Feuerbach 2003, 264
In 1064, Shen Kuo, in his book Dream Pool Essays, gave the earliest written description of the patterns in the steel, the methods of sword production, and some of the reasoning behind it:
From the mid-17th century onwards, European travellers to the Indian subcontinent wrote numerous vivid eyewitness accounts of the production of steel there. These include accounts by Jean-Baptiste Tavernier in 1679, Francis Buchanan in 1807, and H.W. Voysey in 1832.Ranganathan and Srinivasan 2004, 60
The 18th, 19th and early 20th century saw a heady period of European interest in trying to understand the nature and properties of wootz steel. Indian wootz engaged the attention of some of the best-known scientists.Ranganathan and Srinivasan 2004, 78 One was Michael Faraday who was fascinated by wootz steel. It was probably the investigations of George Pearson, reported at the Royal Society in 1795, which had the most far-reaching impact in terms of kindling interest in wootz amongst European scientists.Ranganathan and Srinivasan 2004, 79 He was the first of these scientists to publish his results and, incidentally, the first to use the word "wootz" in print.Bronson 1986, 30
Another investigator, David Mushet, was able to infer that wootz was made by fusion.Bronson 1986, 31 David Mushet patented his process in 1800.Needham 1958, 132 He made his report in 1805. As it happens, however, the first successful European process had been developed by Benjamin Huntsman some 50 years previously in the 1740s.Craddock 1995, 283
Before the introduction of Huntsman's technique, Sheffield produced about 200 tonnes of steel per year from Swedish wrought iron (see Oregrounds iron). The introduction of Huntsman's technique changed this radically: one hundred years later the amount had risen to over 80,000 tonnes per year, or almost half of Europe's total production. Sheffield developed from a small township into one of Europe's leading industrial cities.
The steel was produced in specialised workshops called 'crucible furnaces', which consisted of a workshop at ground level and a subterranean cellar. The furnace buildings varied in size and architectural style, growing in size towards the latter part of the 19th century as technological developments enabled multiple pots to be "fired" at once, using gas as a heating fuel. Each workshop had a series of standard features, such as rows of melting holes, teaming pits, roof vents, rows of shelving for the crucible pots and annealing furnaces to prepare each pot before firing. Ancillary rooms for weighing each charge and for the manufacture of the clay crucibles were either attached to the workshop, or located within the cellar complex. The steel, originally intended for making clock springs, was later used in other applications such as scissors, axes and swords.
Sheffield's Abbeydale Industrial Hamlet operates for the public a scythe-making works, which dates from Huntsman's times and is powered by a water wheel, using crucible steel made at the site.
Huntsman's process was the first to produce a fully homogeneous steel. Unlike previous methods of steel production, the Huntsman process was the first to fully melt the steel, allowing the full diffusion of carbon throughout the liquid. With the use of fluxes it also allowed the removal of most impurities, producing the first steel of modern quality. Due to carbon's high melting point (nearly triple that of steel) and its tendency to oxidize (burn) at high temperatures, it cannot usually be added directly to molten steel. However, by adding wrought iron or pig iron, allowing it to dissolve into the liquid, the carbon content could be carefully regulated (in a way similar to Asian crucible-steels but without the stark inhomogeneities indicative of those steels). Another benefit was that it allowed other elements to be alloyed with the steel. Huntsman was one of the first to begin experimenting with the addition of alloying agents like manganese to help remove impurities such as oxygen from the steel. His process was later used by many others, such as Robert Hadfield and Robert Forester Mushet, to produce the first like mangalloy, high-speed steel, and stainless steel.
Due to variations in the carbon content of the blister steel, the carbon steel produced could vary in carbon content between crucibles by as much as 0.18%, but on average produced a eutectoid steel containing ~ 0.79% carbon. Due to the quality and high hardenability of the steel, it was quickly adopted for the manufacture of tool steel, machine tools, cutlery, and many other items. Because no oxygen was blown through the steel, it exceeded Bessemer steel in both quality and hardenability, so Huntsman's process was used for manufacturing tool steel until better methods, utilizing an electric arc, were developed in the early 20th century. Sheffield Steel and America: A Century of Commercial and Technological Independence By Geoffrey Tweedale. Cambridge University Press 1987 Tool Steels, 5th Edition By George Adam Roberts, Richard Kennedy, G. Krauss. ASM International, 1998, p. 4
The crucible process continued to be used for specialty steels, but is today obsolete. Similar quality steels are now made with an electric arc furnace. Some uses of tool steel were displaced, first by high-speed steel and later by materials such as tungsten carbide.
Early history
Crucible steel is generally attributed to production centres in India and Sri Lanka where it was produced using the so-called "wootz" process, and it is assumed that its appearance in other locations was due to long-distance trade.Feuerbach 2002, 13 Only recently it has become apparent that places in Central Asia like Merv in Turkmenistan and Akhsiket in Uzbekistan were important centres of production of crucible steel.Ranganathan and Srinivasan 2004, 126 The Central Asian finds are all from excavations and date from the 8th to 12th centuries CE, while the Indian/Sri Lankan material is as early as 300 BCE. India's iron ore had trace vanadium and other alloying elements leading to increased hardenability in Indian crucible steel which was famous throughout the middle east for its ability to retain an edge.
South India and Sri Lanka
There are many ethnographic accounts of Indian crucible steel production; however, scientific investigations of the remains of crucible steel production have only been published for four regions: three in India and one in Sri Lanka.Feuerbach 2002, 164 Indian/Sri Lankan crucible steel is commonly referred to as wootz, which is generally agreed to be an English corruption of the word ukko (in the Canarese language) or hookoo (in the Telugu language).Feuerbach 2002, 163
Central Asia
Central Asia has a rich history of crucible steel production, beginning during the late 1st millennium CE.Papakhristu and Rehren 2002, 69 From the sites in modern Uzbekistan and Merv in Turkmenistan, there is good archaeological evidence for the large scale production of crucible steel.Rehren and Papakhristu 2000, 55 They all belong in broad terms to the same early medieval period between the late 8th or early 9th and the late 12th century CE,Rehren and Papachristou 2003, 396 contemporary with the early crusades.
China
The production of crucible steel in China began around the first century BC, or possibly earlier. The Chinese developed a method of producing pig iron around 1200 BC, which they used to make cast iron. By the first century BC, they had developed puddling to produce mild steel and a process of rapidly decarburizing molten cast-iron to make wrought iron by stirring it atop beds of saltpeter (called the Heaton process, it was independently discovered by John Heaton in the 1860s). Around this time, the Chinese began producing crucible steel to convert excess quantities of cast iron and wrought iron into steel suitable for swords and weapons. The Traditional Chinese Iron Industry and its Modern Fate by Donald B Wagner Science and Civilisation in China: Volume 5 by Joseph Needham. p. 345
Ancient people use chi kang, (combined steel), for the edge, and jou thieh (soft iron) for the back, otherwise it would often break. Too strong a weapon will cut and destroy its own edge; that is why it is advisable to use nothing but combined steel. As for the yu-chhang (fish intestines) effect, it is what is now called the 'snake-coiling' steel sword, or alternatively, the 'pine tree design'. If you cook a fish fully and remove its bones, the shape of its guts will be seen to be like the lines on a 'snake-coiling sword'. A History of Metallography by Cyril Smith (1960) p. 45
Modern history
Early modern
The first European references to crucible steel seem to be no earlier than the Post Medieval period.Craddock 2003, 251 European experiments with "Damascus steel" steels go back to at least the sixteenth century, but it was not until the 1790s that laboratory researchers began to work with steels that were specifically known to be Indian/wootz.Needham 1958, 128 At this time, Europeans knew of India's ability to make crucible steel from reports brought back by travellers who had observed the process at several places in southern India.
England
Benjamin Huntsman was a clockmaker in search of a better steel for clock springs. In Handsworth near Sheffield, he began producing steel in 1740 after years of experimenting in secret. Huntsman's system used a coke-fired furnace capable of reaching 1,600 °C, into which up to twelve clay crucibles, each capable of holding about 15 kg of iron, were placed. When the crucibles or "pots" were white-hot, they were charged with lumps of blister steel, an alloy of iron and carbon produced by the cementation process, and a flux to help remove impurities. The pots were removed after about 3 hours in the furnace, impurities in the form of slag skimmed off, and the molten steel poured into moulds to end up as casting .Juleff 1998, 11 Complete melting of the steel produced a highly uniform crystal structure upon cooling, which gave the metal increased tensile strength and hardness in comparison with other steels being made at the time.
Material properties
Previous to Huntsman, the most common method of producing steel was the manufacture of shear steel. In this method, blister steel produced by cementation was used, which consisted of a core of wrought iron surrounded by a shell of very high-carbon steel, typically ranging from 1.5 to 2.0% carbon. To help homogenize the steel, it was pounded into flat plates, which were stacked and forge welding together. This produced steel with alternating layers of steel and iron. The resulting Bar stock could then be hammered flat, cut into plates, which were stacked and welded again, thinning and compounding the layers, and evening out the carbon more as it slowly diffused out of the high-carbon steel into the lower-carbon iron. However, the more the steel was heated and worked, the more it tended to decarburize, and this outward diffusion occurs much faster than the inward diffusion between layers. Thus, further attempts to homogenize the steel resulted in a carbon content too low for use in items like springs, cutlery, swords, or tools. Therefore, steel intended for use in such items, especially tools, was still being made primarily by the slow and arduous bloomery process in very small amounts and at high cost, which, albeit better, had to be manually separated from the wrought iron and was still impossible to fully homogenize in the solid state.
19th and 20th century
In another method, developed in the United States in the 1880s, iron and carbon were melted together directly to produce crucible steel. Throughout the 19th century and into the 1920s a large amount of crucible steel was directed into the production of machine tool, where it was called tool steel.
Elsewhere
Another form of crucible steel was developed in 1837 by the Russian engineer Pavel Anosov. His technique relied less on the heating and cooling, and more on the quenching process of rapidly cooling the molten steel when the right crystal structure had formed within. He called his steel bulat steel; its secret died with him. In the United States crucible steel was pioneered by William Metcalf.
See also
Notes
External links
|
|
